Bitmain Antminer D3 (17.5Gh)

The Bitmain Antminer D3 (17.5Gh) is an ASIC built for the X11 algorithm that quietly does its job at 17.5 gigahashes per second while drawing 1,280 watts, a configuration that makes it most effective for Dash and other X11-based coins where electricity is cheap and steady; compact at 130 x 190 x 320 mm and weighing 5.5 kg, it slips into racks or small rigs without dominating a room, though its 75-decibel operating noise-comparable to a running vacuum-means thoughtful placement or acoustic isolation is sensible for inhabited spaces. Its dual high-speed fans and three-hash‑board layout, housed in a precision die-cast aluminum alloy chassis, enhance heat dissipation and mechanical durability so sustained runs stay within thermal limits, and built-in remote monitoring plus overheat and hardware-fault alerts help detect problems early and reduce downtime if a fan slows or a board underperforms. Newer miners outpace the D3 on efficiency, but in regions with low-cost or renewable-sourced power it can remain a pragmatic choice; pairing such units with solar, wind, or community microgrid generation and using captured waste heat for drying, greenhouses, or space heating can tilt long-term economics and environmental impact in a more humane direction. Before deploying, run a profit calculation that compares expected daily, monthly and annual coin yields against measured electricity rates and cooling overhead, account for network difficulty and pool fees, ensure adequate ventilation and electrical provisioning, and plan for preventative maintenance-regular fan checks, dust management, and firmware updates-to preserve hash rates and extend hardware life. Seen from the sober vantage of someone who has watched conflict and scarcity, the D3 is not a silver bullet but a tool: efficient enough to matter where infrastructure and energy choices permit, clear in its limits, and best used with an eye toward resilience, community power solutions, and the practical work of keeping machines running so people can live better lives despite the storms beyond.

Listen-take this into your hands as if you were opening a small, humming engine of consequence: the Bitmain Antminer D3 pushes 17.5 gigahashes per second with a steady draw of about 1,280 watts, powered by BM1760 ASICs and a custom control board tuned for long sessions so hash-rate wobble is the exception, not the rule; it is compact-130 x 190 x 320 mm, 5.5 kg-so it slips into racks and tight spaces, but it speaks loudly at roughly 75 decibels, a constant vacuum-cleaner companion that demands you think about placement or acoustic isolation. Feel the chassis-precision die-cast aluminum-conducting heat to dual high-speed fans and three hash boards, a practical geometry of cooling that, paired with remote monitoring and built-in overheat and fault alerts, keeps you a step ahead of failure if you listen to the telemetry; yet know this: it has no modern auto-tuning miracles, so you must handcraft efficiency with power-limit adjustments, firmware choices, and careful airflow, because early batches needed firmware attention and stability remained a live concern for some units. Use it where it makes sense-cheap, steady electricity or experimental benches where you trial algorithms, reuse waste heat for a greenhouse or drying shed, or tie units into community microgrids and renewable arrays to tilt the carbon balance-and before you switch it on, run the numbers: expected coin yield against measured kilowatt-hours, anticipated network difficulty, pool fees, and the real cost of cooling and ventilation. Plan the obvious: adequate circuit provisioning, clean intake paths, regular fan inspections, dust management, scheduled firmware updates and spare fans or boards on hand; treat the D3 not as a silver bullet but as a disciplined tool-a reliable, blunt instrument for X11 mining in niches where infrastructure and energy choices make it practical, and a machine that rewards attention, preventative care, and smart integration into a broader, resilient energy or experimental setup.

X11 is een cryptografische hashfunctie die als ruggengraat dient van Dash proof-of-work consensusmechanisme. Dit algoritme verwerkt invoergegevens van elke lengte en produceert een vaste hash-waarde, wat zorgt voor veiligheid en integriteit in het miningproces.